(주)코린스

분류 검색

현재위치 : Home > > >

 
이전 큰 이미지 다음

Level Control W/Nema 4 Housing

제조사 : DAVIS
제품번호:DV725101
판매가격  : 원
포인트 : 점
수량 :
  PLUS   MINUS   개
■ 회원가입을 하시면 할인된가격을 보실수 있습니다.
■ 모든가격은부가세별도 입니다.
■ 회원이 되시면 가격변동정보, 신제품, 특판제품, 기술정보등 다양한
뉴스정보를 보내드립니다.
■ 30만원미만은 택배비 3,000원(착불)입니다.
■ 카드결재시 세금계산서 발행 불가합니다.
■ 배송은 평균 2~3일정도 예상됩니다.

상세페이지를 마이피플로 보내기 - 웹용 상세페이지를 twitter로 보내기 상세페이지를 facebook으로 보내기 상세페이지를 Me2Day로 보내기

This housing is integrally mounted on the rear of the probe. The Cap Point/511 always uses either a F.P.
The Cap Point/511 system consists of an electronic amplifier mounted in a cast aluminum explosion proof housing. This housing is integrally mounted on the rear of the probe. The Cap Point/511 always uses either a F.P. (guarded polypropylene) or GT (guarded Teflon®) probe assembly (see below). Probes are manufactured in a variety of insulating materials and metals. The active length of the probe will vary subject to the specific application of the system. The probe may be mounted in a vertical or horizontal position. Normally, the probe is threaded into the process vessel with a 3¼4" connection. The probe is energized with a radio frequency signal (about 2 megahertz). When the process level changes, a change of capacitance occurs, resulting in a small change in frequency. This change is compared with preset values in the electronic measuring circuit. After proper amplification, this signal is used to provide a change of state condition which operates the relay. 

The CAP POINT/511 is pre-calibrated to operate in any size vessel, provided the tank's physical dimensions are greater than one foot in diameter. Smaller vessels or probes installed in pipes must be dynamically calibrated, i.e. installed in process vessel and calibrated to your exact conditions. Installation with products that have dielectric constants of less than 1/5 should be dynamically calibrated. The pre-calibration permits application to the control of any product with a dielectric constant from 1.5 to 80.0 (light hydrocarbons, plastic pellets to water acids and slurries). A time delay is provided to eliminate the effects from turbulence. 

The CAP POINT/511 utilizes a guarded probe that eliminates any shift in control point due to build up of product.

 
Primary areas of Applications
  • The CAP POINT/511 is an ideal solution for many level control problems. Most liquids are potential applications for the Cap Point/511 as are free flowing granular products.
  • Liquids-Petroleum Products: Eg: Crude Oil, Refined Oil, Kerosene, Ethylene Glycol, Gasoline, etc.
  • Liquids-Organic Solvents: Eg: Ethylene, Methyl and Isopropyl Alcohol, as well as Toluene, Heptane, Turpentine, Acetone, etc.
  • Liquids-Conductive: Eg: Water, acids, diluted acids (within the limits of probe sensor gland housing and insulation materials), water with impurities
  • Liquids-Interface: Eg: Petroleum products and water (with calibration)
  • Bulk Solids: Eg: Cereal grains, plastic pellets and powders, sand, ores, crushed coal, coke and other free flowing granular products *Note: Resistance to corrosion is determined by insulating materials
 
Features
  • Versatile A single calibration permits the application on any product with a dielectric constant from 1.5 (light hydrocarbons, plastic pellets) to 80.0 (water, acids and slurries)
  • Fail Safe A simple field selection determines the High or Low FAIL-SAFE mode
  • Immune to Product Buildup A “Guarded Probe” prevents any shift or loss of calibration due to build up of conductive or non-conductive materials
  • High Sensitivity - Sensitivity is .5 pfd or less. The Cap Point/511 system will reliably detect any product whose dielectric constant is 1.5 or higher without field calibration.
  • Rugged Totally solid state electronics mounted in an explosion proof cast aluminum housing
  • Immune to Static The probe input circuit is protected from static electrical discharges
  • RFI Immunity The circuit is immune to RFI
  • Power Supply The Cap Point/511 will operate with either 115 VAC, 230 VAC 50-60 Hz power source or 24 VDC
  • Versatile A field adjusted time delay is available to provide protection from turbulent level conditions
  • Shop Calibration The CAP POINT/511 system is designed to be installed without field calibration in most applications
 
 
CAT NO. MODEL DEscRIPTION AVAIL PRICE 
DV725101   511 B   LEVEL CONTROL W/NEMA 4 HOUSING   Yes   745,200
DV725102   GIMN   14" PROBE DRY PRODUCTS (NON- CORROSIVE)   Yes   378,000 
DV725103   GT   18" PROBE FOR LIQUIDS CORROSIVES *NEW   Yes   615,600